HC-06 HC 06 RF Wireless Transceiver Slave Module RS232 TTL to UART | Asia Sell

HC-06 HC 06 RF Wireless Transceiver Slave Module RS232 TTL to UART

  • $13.60
Tax included. See the Shipping Rates Table. Calculated at checkout (combined weight and service dependant). Free shipping for orders over $50.
0 in stock This item is yet to be reordered. You are welcome to place an order and we will order more right away. You can click the bell at bottom left to be notified when the item is back in stock.

DESCRIPTION

  • 1 Piece.
  • HC-06 HC 06 RF Wireless Transceiver Slave Module RS232 TTL to UART.
  • GPS receiver.
  • Industrial control.
  • MCU projects.
  • Default serail port setting : 115200 (optional 4800,9600,19200), N, 8, 1.
  • Pairing code : 1234.
  • Running in slave role: Pair with BT dongle and master module.
  • Coupled Mode: Two modules will establish communication automatically when powered.
  • PC hosted mode: Pair the module with dongle directly as virtual serial.
  • protocal : Specification v2.0+EDR.
  • Frequency : 2.4GHz ISM band.
  • Modulation : GFSK(Gaussian Frequency Shift Keying).
  • Emission power : 4dBm, Class 2.
  • Sensitivity : -84dBm at 0.1% BER.
  • Speed : Asynchronous: 2.1Mbps(Max) / 160 kbps, Synchronous: 1Mbps/1Mbps.
  • Security : Authentication and encryption.
  • Profiles : serial port.
  • CSR chip : v2.0.
  • Wave band : 2.4GHz2.8GHz, ISM Band.
  • Protocol : V2.0.
  • Power Class : (+6dbm).
  • Reception sensitivity: -85dBm.
  • Voltage : 3.3 (2.7V4.2V).
  • Current : Paring - 35mA, Connected - 8mA.
  • Temperature : -40C~ +105C.
  • User defined Baud rate : 4800, 9600, 19200, 38400, 57600, 115200, 230400.
  • 460800,921600 ,1382400.
  • Dimension : 26.9mm*13mm*2.2mm.

Pin definition

  • PIO8 connects with LED cathodea with 470ohm series resistor in betweenLED NEGATIVE connects to groundIt is used to indicate the module stateAfter powered on, flashing intervals differ in different states.
  • PIO9 is used to control LED indicating paringIt will be steady on when paring is successful.
  • PIO11, module state switching pinHIGH -> response to AT command; LOW or floating -> regular work status.
  • With build-in reset circuit, reset is completed automatically after powered on.
  • Steps to set to MASTER: .
  • Set PIO11 HIGH with a 10K resistor in between.
  • Power on, module comes into AT Command Response Status.
  • Open HyperTerminal or other serial tool, set the baud rate 38400, 8 data bits, 1 stop bit, no parity bit, no Flow Control.
  • Via serial port, send characters "AT + ROLE = 1 r n",if successful, return "OK r n", where r n is carriage return.
  • Set PIO11 LOW, re-power, then in Master state, automatically search for slave module and connect.

Customer Reviews

Based on 1 review
100%
(1)
0%
(0)
0%
(0)
0%
(0)
0%
(0)
T
T.R.
Fast Postage, Item as described, would buy from again, A+++
Click to edit the product in Ali Orders.
Note: only show for shop owner